See RaggTopp Fabric Cleaner and Protectant above. I hope someone finds this useful, I would have liked to have had it when I did the job myself. Push the plastic channel and leather tabs through the crack in the seat. Made by hand in Italy, quality and consistency are second to none. Snap-in ends and eyebolts are sold separately if you want to install your belts in that manner.
A 45Es right or left unlatch movement prevents accidental opening and precise spring pressure provides a positive feel. They are easily reset with this reliable low cost service light reset tool. Using the included three bar slide you can mount the belts by either wrapping them around a rollbar or by bolting them in place. I found that they covered the major points of the procedure, but missed many of the little details that made the job particularly nasty. Use your can of Gummi Pflege to treat all rubber seals.
Simply remove two of the lug bolts and screw in a Wheel Pin in each location, then remove the remaining lug bolts. This will help prevent collateral damage to your interior while you are wrestling the seat out of the car. Read through this procedure before digging in. If the original item or suitable replacement part is not available, then this warranty is void. I couldn't reach these rings, so I couldn't pull the cover up all the way. Seat Compatability: Schroth approves this harness only for stock seats or seats that have passed independent crash testing.
If you're working with the electrical system, disconnect the battery before beginning. It is very easy to scratch things with the seat brackets while removing the seat hence the towels. These next step is important, move the seat to the all the way back position. These pads simply cover the belts and fasten with a zipper. Otherwise, your hand - or glove - has to yank on the end of the strap which might be slippery. Precise internal spring pressure allows a positive feel on the 45Es right or left unlatch movement that reduces the chance of accidental opening.
Check your cage tubing diameter especially if your car was built in Europe as they used metric tubing sizes. I'm potentially looking at swapping this out as mine has snapped on the drivers side the plastic clip which fits into the seat at shoulder level and guides the seat belt can these be purchased from anywhere or should i glue? Remove the two plastic plugs at the bottom of the rear plastic shell. A fun, sporty little 2 seater came both in convertible and coupe form. Just replace the seat bushings. You'll know if it doesn't feel loose once the sides are detached. Using diagonal cutters, clip the zip-tie holding the sensor wire to the seat frame.
The only other option is to replace the stitching by hand. There are 4-5 connectors per seat. You can open these rings up by forcing a screwdriver into the overlapping part and twisting it open. Meguiar's 17 and 10 are intended to be a restoration product. This is a must for all roadster owners. Please note if your seat belt guide is no longer attached to the seat this device will not work. My problem is the removal of the plastic seat back.
Also, remember that you cannot drive the car until both seats are done sensors, remember? Langka removes excess touch up paint leaving the chip area smooth and even with the paint on your vehicle. The sizes of the nuts and bolts we give may be different from what you have, so be prepared with different size sockets and wrenches. This Camlock belt set comes in a six 6 point configuration with a pull-down lap belt design. You can now pull the cover nearly all the way off, but enough to give you access to remove and add the new seat belt guides. Made by hand in Italy, quality and consistency are second to none. Using a small screwdriver, push the black center portion in towards the seat. We also provide inexpensive and guaranteed 3 day, 2 day, and Overnight shipping options, so if you need your Seat Belt Guide - Driver Side tomorrow, eEuroparts.
Insert two lug bolts to hold the wheel in place and then remove the Wheel Pins and install the remaining lug bolts. Get all of the straps free of the seat frame and pull the seat skin off of the seat. All of there hardware and brackets are constructed from drop-forged steel and are cadmium plated for strength and corrosion resistance. There are plastic hooks on the shell circled that snap onto the seat circled. The available colors are Black, Blue, or Ingrid.