By using a mirror type finish along with a light ion coating to clean up the light, these Oldsmobile Bravada High Beam Headlamp Replacement Bulbs produce a very clean white light that from certain angles shows tints of brilliant violet and red. Undo all three completely and place somewhere safe, the headlamp unit will become loose. The retainers for the left assembly are in front of the washer fluid reservoir. The whole thing threads on to the end of the water pump. This is especially true in rain, snow, and foggy conditions, as the yellow color causes less glare, thus the reason many foglamp Bulbs are yellow. It will come out and you will have access to the back so you can replace the bulbs. Unscrewing the bezel frame allows the bulb to come out.
Once I get the new bulbs in I will post a response of what I think of them. It is pretty complicated for such an easy task Buy a 2002 Chevy trail blazer haynes manual. Each of the headlight assemblies are braced through the radiator support with a pair of retainers. Do this by removing the torx screw that is in the corner of the groove between the headlight and turn signals. The 02s usually have the plastic tabe style retainers. If they make noise or rotate roughly, replace them also. Remove the retainers by pulling up on the retainer.
There is a wire that holds the bulb in. Flip the clip all the way up. Your feeling for a rubber gasket round dark colored rubber thing, reminds me of the tub stopper. Pull up on the tabs that release the light housing. Daniel Stern does not post much, if at all, here anymore but he is very knowledgeable about all phases of lighting. This is done by unscrewing the 10 millimetre screws, one at each end, using the socket and extension then using your fingers to release the clip at each end which holds the grill in place.
Once the bulb is in position move the metal clip down and toward the driver's side and secure the little ring end to hold the bulb in place. You will also need to unfasten the rubber weather stripping mounted on button-hole style knobs, two on the headlight and two on the signal … assembly. Near Cooperstown, New York Life is not like a box of chocolates it's more like a jar of jalapenos- what you do today could burn your ass tomorrow! If there is no ground plate you will only need to remove the hot wire from the base of the bulb leaving the ground wire in place 7 Put the bulb in and clip it in place being sure the metal clip is all the way up. Their staying power in the market is a testament to the clean white color this coating produces, and of their Low Beam Headlamp Bulbs incredible durability resulting from superior components and meticulous manufacturing practices. You will need to remove the washer tank and air filter housing to get a clear view of it.
I don't know the size, because rather than break out all my wrenches, I just grabbed an 18 inch crescent wrench. Note which way the bulb fits into the headlamp. On the bottom of the bulb housing you will see a little ring. I only had to move the cross brace on the drivers side low beam in order to change it. You may need to remove the Engine Coolant overflow tank to remove the blower motor. At the back of the headlamp unit, push down the clip holding the plastic weathershield in place and remove the weathershield by pulling it outwards and down so that the lugs at the top come out of their holes.
Slide this base over the spade terminal end of the new bulb with the flat sides of the bulb base and ground plate aligned. Lift the retaining clip on the wire connector jus … t enough to pull the connector from the bulb socket. No brighter or whiter light, nadda. Make sure that the air box is properly aligned with it. Doing this will make it easy to reinstall the cover.
Though they are widely distributed throughout the industry, and their quality rivals that of the German and Japanese lighting giants, they do almost no marketing, instead pouring every dollar into the development and optimization of their Fog Lamp Bulb line. The head of these bolts fits onto notches on the bezel. Pull out the plug that gives the light bulb juice, and remove the rubber seal around it. I bought a set for both my at the time '01 Montana and '96 Bonneville. This will allow you to pull out the fibreboard sufficiently to get your hand up the inside of the wing. Once these two wingnuts are removed, carefully remove the who … le assembly.
The retainers for the left assembly are in front of the washer fluid reservoir. Remove the retainers by pulling up on the retainer. I have replaced those wires on this model and it may be a simple connection problem. Re-fit the electric plug and replace the weathershield, first making sure that the rubber gasket is in its grove properly. Remove the bulb from the rubber gasket change it and then put it back together And its veryyyyyyyy simple, if it helps I'm a female and did this very quickly no I'm not a mechanic either Good job pcsgrp35se.